Self-Drilling Screws in Ground-Mounted PV Plants: Key Points and Common Issues

Self-Drilling Screws in Ground-Mounted PV Plants: Key Points and Common Issues

Self-Drilling Screws in Ground-Mounted PV Plants: Key Points and Common Issues

Ground-mounted plants rely heavily on self-drilling screws to join mounting rails to purlins. They are fast and economical, but the plant must survive twenty-plus years of wind loads, temperature cycles and corrosion in the open. O&M records show recurring failures: screws backing out, washers aging into leaks, and corrosion at aluminum-steel contacts. Most of these can be prevented at selection and construction. This article reviews the application points for engineering and O&M teams.

Purlin Matching: Thickness and Grade Decide Everything

Drill points and threads must match the purlin. A common problem is screws selected for thin-gauge purlins meeting heavier or hot-rolled sections on site, burning points or refusing to pierce; another is insufficient thread engagement, where a seemingly tight joint holds only two or three engaged turns and loosens under wind loads quickly. Verify the actual thickness of delivered purlin batches before construction and keep trial-driving records per substrate. For combinations beyond normal drilling capacity, switch to pre-drilling and threading instead of forcing a long point through.

Wind-Load Vibration: Preload and Loosening Over Time

Ground plants present a large windward area, and rails micro-vibrate under gusts, so thread preload decays over the years. Joints relying on thread friction alone can show visible back-out after years of vibration. Three common counters: ensure enough clamp force and engagement length so friction surfaces are fully loaded; use integrated washer screws with controlled torque; and add mechanical retention or bolt-nut-with-spring-washer solutions at critical nodes. During O&M, checking back-out and washer status as mandatory items catches loosening early.

Galvanic Corrosion: Aluminum Rails Meeting Steel Screws

Aluminum rails in direct contact with steel self-drilling screws form a classic galvanic pair in humid and salty environments: aluminum, the anode, is consumed, white corrosion products appear at the contact, and joints loosen. Mitigations include screws with isolation coatings or plastic isolation washers, preferring stainless connection parts, and applying protective grease to contact faces. Coastal plants should treat galvanic corrosion as a dedicated acceptance and patrol item, treating contact faces and recording locations when white products appear.

Washer Aging and Sealing Management

The EPDM washer is the first line against water, but UV, heat and ozone harden and crack it over time. Washers usually fail before the screw itself, showing as water marks at joints after rain. Schedule pre-rainy-season spot checks of washer condition and replace at defined compression set or surface cracking levels, checking screw torque at the same visit. Spare parts should match original washer specs, since mismatched thickness disturbs sealing.

Construction Quality: Torque and Tool Management

Site work decides quality. Self-drilling screws are torque-sensitive, and crews used to plain tools easily slip or overdrive. Effective controls: torque-limited clutches with periodic calibration, first-batch trial driving and torque spot checks for new crews, and tracking tilted driving and washer damage rates as crew quality metrics. These cost little yet sharply reduce later O&M burden; many plant repair records show failures concentrated in a few crews, which shows the value of management and training.

Extra Considerations for Extreme Climates

Different climate zones stress fasteners differently: cold regions raise concern for steel toughness and washer elasticity at low temperature, with brittle-failure risk during installation, favoring tougher materials and low-temperature EPDM grades; desert sites see wide day-night swings and abrasive dust, making coating wear resistance and ozone aging of washers the focus; humid coastal zones put salt spray and galvanic corrosion first. Before selection, build a climate factor list for the site and confirm countermeasures item by item with the supplier, which is far cheaper than remediation afterwards. Patrol frequency and check items should follow the climate zone as well, not one national template applied everywhere.

O&M Inspection and Failure Tracing

Plant areas are large, so inspection needs method: patrol routes per array block, focusing on windward sides, grounding connections and areas with prior leak records. When a failed screw is found, record location, batch and failure mode, whether back-out, corrosion break or washer aging, so the supplier can trace coating batch and process records. FASTKING keeps full batch archives for PV customers, and with patrol photos can quickly determine whether the issue is batch-wide, avoiding wasteful blanket replacement.

Summary

Self-drilling screw issues in ground plants are, at root, matching problems: point to purlin, coating to environment, locking to wind load, inspection to aging cycle. Nail these four matches and the fasteners quietly serve the plant through its design life instead of populating the O&M checklist.

Contact

Contact: Lizhong Deng

Phone: 13928071304

Tel: +86-756-8586520

Email: sales@jlfastener.com

Add: Room 56-301,Mingzhubeilu 388hao,Xiangzhou Area,Zhuhai City,GuangDong,China